Square row
NT-S5296P196V1 publishes a 196×156 mm footprint and a weight of 4.89 kg.
52 / 96 mm combination plate
52/96 Combination Zero-Point Plate
Manual plates that locate 52 mm and 96 mm pull studs
Square NT-S5296P196V1 and round NT-S5296P230V1 are the published manual combination plates. Both catalogue rows list 30 kN clamping force, 4 × 90° indexing, and repeat positioning accuracy of <0.005 mm. Match the pull stud and the approved drawing before treating a vise or fixture as compatible.
30 kN clamping forceCatalogue value on both published rows. Installed holding still depends on the stud, the joint, and the cut.
<0.005 mm repeat positioningCatalogue repeat positioning accuracy. Confirm seating on the approved drawing and on the machine.
Square or roundSquare footprint 196×156 mm or round footprint φ230 mm. Both rows list a height of 27 mm.
Standard models in stock
Custom hole patterns
HMC / VMC / 4th / 5th axis
Quality documents scoped at RFQ
MIC Audited Supplier
Product overview
One manual plate for both stud families
Use this plate when one machine-side base has to accept both a 52 mm pull stud and a 96 mm pull stud. The square row is NT-S5296P196V1. The round row is NT-S5296P230V1. Each row lists manual actuation, hardened stainless steel, and the same two pull studs, NT-S52P16V1 and NT-S96P20V1.
Round row
NT-S5296P230V1 publishes a φ230 mm footprint and a weight of 9.5 kg.
Shared studs
NT-S52P16V1 for the 52 mm side and NT-S96P20V1 for the 96 mm side.
Manual actuation
Both rows are Manual. These two catalogue rows do not list an air-release figure.
Published catalogue rows
Compare the square and round plates
These rows are the 2026 NEXTAS quick-change catalogue values for the two named models. They do not replace the approved drawing or a machine acceptance check.
| Specification | NT-S5296P196V1 | NT-S5296P230V1 |
|---|---|---|
| Product code | NT-S5296P196V1 | NT-S5296P230V1 |
| Footprint | 196×156 mm | φ230 mm |
| Height | 27 mm | 27 mm |
| Clamping force | 30 kN | 30 kN |
| Weight | 4.89 kg | 9.5 kg |
| Pull studs | NT-S52P16V1, NT-S96P20V1 | NT-S52P16V1, NT-S96P20V1 |
| Actuation | Manual | Manual |
| Repeat positioning | <0.005 mm | <0.005 mm |
| Indexing | 4 × 90° | 4 × 90° |
Selection and mounting
Match the stud, the vise, and the table
- Choose NT-S5296P196V1 when the base has to be square, and NT-S5296P230V1 when it has to be round. The catalogue lists both heights as 27 mm.
- The 52 mm vise or fixture needs pull stud NT-S52P16V1. The 96 mm vise or fixture needs pull stud NT-S96P20V1. A 52 mm stud does not lock in a 96 mm seat.
- Send the machine table drawing and match it to the catalogue plate drawing before you drill or mount the plate.
- Repeat positioning is listed as <0.005 mm. Treat that as the catalogue figure. Confirm the seated setup on the drawing and on the machine before you release the job.
Applications
Where these two plates fit
Mixed stud families
One machine-side base for a 52 mm pull stud and a 96 mm pull stud, after each stud matches the drawing.
Square base
NT-S5296P196V1 when the fixture stack needs the published rectangular footprint.
Round base
NT-S5296P230V1 when the table clearance calls for the published round footprint.
Vise change on a fixed plate
The plate can stay on the machine while the vise changes, once the stud and the drawing agree.
Frequently Asked Questions
Which published model is square, and which is round?
Square NT-S5296P196V1 lists footprint 196×156 mm. Round NT-S5296P230V1 lists footprint φ230 mm.
Which pull studs do these plates use?
Both published rows list NT-S52P16V1 and NT-S96P20V1. Use the stud that matches the vise or fixture, and confirm the pair on the drawing.
Is the clamping force the same on both rows?
Both catalogue rows list 30 kN. That is the published clamping force, not a measured result for a particular cut.
Does the catalogue repeatability replace a machine check?
No. The catalogue lists <0.005 mm. Seating, datum, and the cut still have to be confirmed on the approved drawing and on the machine.
What should I send for a quote?
The machine table drawing, the choice of NT-S5296P196V1 or NT-S5296P230V1, the vise or fixture with its pull stud, the workpiece envelope, and the quantity.
Fast quote
Request a 52/96 combination plate quote
Name, work email, and the machine with the square or round model are enough to start. The reply confirms the pull stud and the catalogue row after the table and vise drawings are reviewed.